How can a magnet light a bulb with NO battery?
Wave a magnet in and out of a coil of wire and a meter jumps. Spin a coil between magnets and a bulb glows. This is how power stations make the electricity in your home, and how a transformer lowers the voltage for your phone charger.
In this lesson you will see that electric currents make magnetic fields, that a magnetic field can push a wire (the motor), and that a changing magnetic field can make a current (the generator and the transformer).
🎧 Warm-up: make a prediction
By the end of this lesson, you will be able to…
- 1Explain a magnetic field and show the field around a straight wire and a coil, using the right-hand grip rule.
- 2Explain electromagnets and name their applications.
- 3Find the direction of the force on a current in a field with Fleming’s left-hand rule and use F = BIL.
- 4Explain electromagnetic induction, state Faraday’s and Lenz’s laws and use Fleming’s right-hand rule.
- 5Describe AC and DC generators.
- 6Explain the transformer, solve problems, explain power losses and why the core is laminated.
The magnetic field
A magnetic field is the region around a magnet (or a moving charge, or a current) where a magnetic force can be felt. We draw it with field lines. Outside a magnet the lines go from the N pole to the S pole. A compass needle lines up with the field, and its N end points along the field. The closer the lines, the stronger the field. The field strength is called the magnetic flux density B, measured in tesla (T). Like poles repel, unlike poles attract.
Drawn from N to S outside the magnet. They never cross. Close together = strong field.
The strength of the field, in tesla (T). A fridge magnet is about 5 mT.
A tiny magnet that turns to point along the field. Its N end shows the field direction.
A wire carrying current is surrounded by a magnetic field
In 1820 Oersted saw a compass needle twist near a wire carrying current. So moving charges make magnetic fields. Around a long straight wire the field lines are circles centred on the wire. Use the right-hand grip rule: point your thumb the way the (conventional) current flows, and your curled fingers show the field direction. The field gets weaker with distance: B = μ₀I ÷ 2πr. In a solenoid (a long coil) the fields of all the turns add up to a strong, nearly uniform field inside: B = μ₀NI ÷ L. Curl your fingers the way the current goes round and your thumb points to the N pole.
Try it: reverse the current and watch the compass turn round. Double I (B doubles). Double r (B halves). On the solenoid tab, the N pole is the end the field comes out of.
The electromagnet
An electromagnet is a solenoid wound on a soft iron core. The iron becomes magnetised and makes the field much stronger (here about 6 times). It is made stronger by using more turns, a bigger current, or a soft iron core. It is a temporary magnet: switch off the current and it loses its magnetism (soft iron demagnetises easily; steel would stay magnetised).
Try it: count the clips. Change the turns, the current and the core. Then switch off.
The electromagnet pulls the hammer to the gong and breaks the circuit. The spring pulls it back and the circuit is made again. It rings over and over.
A small current in an electromagnet closes a switch in a big-current circuit. A safe way to switch heavy loads.
A scrapyard crane lifts scrap iron and drops it when the current is switched off. A loudspeaker moves a cone with a changing current in a coil.
What happens to the electromagnet?
Sort each change into Stronger, Weaker or Stays the same strength.
A magnetic field pushes on a current
A wire carrying a current has its own magnetic field. Put it in another magnetic field and the two fields interact, so the wire feels a force. This is the motor effect. The force is largest when the wire is at 90° to the field and zero when it lies along the field. The size is F = BIL sinθ (use F = BIL for 90°), where B is the flux density, I the current and L the length of wire in the field. The force is at right angles to both the field and the current.
Try it: the wire is a ⊙ (current out of the page). Which way is the force? Reverse the current. Reverse the field. Then try the tilt tab and bring the angle down to 0°.
Use your LEFT hand for motors
Stretch your left hand so the thumb, first finger and second finger are all at right angles (like the corner of a box). First finger = Field (N to S). seCond finger = Current (+ to −). Thumb = Thrust (force) or motion. Remember F-B-I for Force, B field, I current: thumb, first, second.
Try it: choose a field and a current. The thumb shows the force. Check it with your own left hand! Then swap the current direction: the thumb swaps too.
A coil in a field turns: the electric motor
A coil in a magnetic field carrying a current has forces on its two long sides that are equal and opposite, so the coil turns. After half a turn the forces would pull the coil back, so a split-ring commutator reverses the current every half turn and keeps the coil turning the same way. A stronger motor needs more turns, a bigger current, a stronger magnet, or an iron core. Two brushes press on the commutator.
Try it: switch on with the split ring. Increase I or B. Then choose slip rings: the coil rocks and settles. Why? The commutator is the secret.
Motor effect: sort and order
Sort each item into Increases the force or Does not change the force on a wire in a field.
🔢 Put the steps in order: how the DC motor keeps turning
A changing magnetic field makes an emf
In 1831 Faraday found that you can make a current with a magnet. Electromagnetic induction is the production of an emf (voltage) in a conductor when the magnetic field through it changes, or when the conductor cuts through magnetic field lines. If the circuit is complete, the emf drives a current. Three important facts: a stationary magnet gives no emf; faster movement gives a bigger emf; reversing the movement (or the pole) reverses the emf.
Try it: drag the magnet position slowly, then quickly. Hold it still inside the coil: no emf. Use more turns or a stronger magnet. Switch to the S-pole tab.
Faraday’s law and Lenz’s law
Magnetic flux Φ is the field passing through a coil: Φ = BA (B at right angles to the area A), measured in weber (Wb). Faraday’s law: the induced emf is directly proportional to the rate of change of magnetic flux linkage (rate of cutting flux). ε = N ΔΦ ÷ Δt. Lenz’s law: the induced current flows in the direction that opposes the change that produced it. The minus sign in ε = −N ΔΦ/Δt shows this. Lenz’s law is conservation of energy: pushing the magnet in is hard because the coil pushes back, and the work you do becomes electrical energy.
Worked example 1: A coil of 100 turns has its flux fall from 0.04 Wb to 0.01 Wb in 0.5 s. Find the induced emf.
- Change of flux: ΔΦ = 0.04 − 0.01 = 0.03 Wb.
- Faraday: ε = N ΔΦ ÷ Δt = 100 × 0.03 ÷ 0.5.
- ε = 6 V (the minus sign only tells us the direction opposes the change).
Worked example 2: A field of 0.2 T passes at right angles through a coil of area 0.05 m². Find the flux.
- Φ = BA = 0.2 × 0.05.
- Φ = 0.01 Wb.
Use your RIGHT hand for generators
For a wire moving through a field, hold your right hand with thumb, first and second fingers at right angles. Thumb = Motion of the wire. First finger = Field. Second finger = induced Current. (Left hand for motors, right hand for generators. Remember: “Right = gen-Right-ator”.) A straight wire of length L moving at speed v at right angles to the field has an emf ε = BLv.
Try it: pick the field and the motion. The second finger shows the induced current. Check with your right hand.
Worked example 3: A wire 0.5 m long moves at 6 m/s at right angles to a field of 0.4 T. Find the emf.
- ε = BLv = 0.4 × 0.5 × 6.
- ε = 1.2 V.
Spin a coil in a field: a generator
A generator turns movement energy into electrical energy. A coil spins in a magnetic field, so the flux through it keeps changing and an emf is induced: ε = NBAω sinφ. The emf is zero when the coil is perpendicular to the field (flux is largest but not changing) and maximum when the coil is parallel to the field (the sides cut the field fastest). An AC generator uses two slip rings, one for each end of the coil, so the output reverses every half turn. A DC generator uses a split-ring commutator, which swaps the connections every half turn, so the current in the outside circuit always flows one way (but it pulses). Faster spin, more turns, a stronger field or a bigger coil give a bigger emf.
Try it: pause the coil, drag the angle slider and find where the emf is zero and where it is biggest. Compare the AC tab with the DC tab. Double the speed: the emf and the frequency both double.
Motor or generator?
Sort each description into Motor or Generator.
🔢 Put the steps in order: how a generator makes electricity
A transformer changes an AC voltage
A transformer has two coils, the primary (input) and the secondary (output), wound on a soft iron core. An alternating current in the primary makes a changing flux in the core. The core carries this flux through the secondary, where it induces an alternating emf (mutual induction). Because the turns differ, the voltage changes: Vs ÷ Vp = Ns ÷ Np. More turns on the secondary = step-up. Fewer = step-down. A transformer works only with AC, because DC gives a steady flux with nothing changing. For an ideal transformer there is no power loss: VpIp = VsIs, so when the voltage goes up, the current goes down.
Try it: make Ns bigger than Np: a step-up. Smaller: a step-down. Watch Ip and Is. Then switch to DC and see what happens. Lower the efficiency to see power lost as heat.
Using the transformer equations
For an ideal transformer: Vs = Vp × Ns ÷ Np. Is = Vs ÷ R. And VpIp = VsIs. The efficiency of a real transformer is η = (power out ÷ power in) × 100%.
Worked example 4: An ideal transformer has 1000 turns in the primary and 50 turns in the secondary. The primary is connected to 240 V AC and the secondary to a 6 Ω load. Find Vs, Is and Ip.
- Vs = 240 × 50 ÷ 1000 = 12 V (step-down).
- Is = Vs ÷ R = 12 ÷ 6 = 2 A.
- Power out = 12 × 2 = 24 W. Ideal: power in is also 24 W.
- Ip = 24 ÷ 240 = 0.1 A. (Check: Ip ÷ Is = Ns ÷ Np = 0.05 ✓.)
Worked example 5: A transformer takes 500 W from the supply and delivers 450 W. Find its efficiency and the power lost.
- η = 450 ÷ 500 × 100 = 90%.
- Lost = 500 − 450 = 50 W (as heat).
Why a real transformer is not 100% efficient
The coil wires have resistance, so current heats them. Remedy: use thick copper wire of low resistance.
The changing flux induces swirling currents inside the iron core that heat it. Remedy: make the core from thin laminated sheets.
The core is magnetised one way, then the other, 100 times a second (50 Hz), and this wastes energy as heat. Remedy: use soft iron (or silicon steel) that magnetises and demagnetises easily.
Not all of the flux from the primary links with the secondary. Remedy: wind the coils one over the other on a closed core.
Good large transformers reach over 98% efficiency. The lost energy appears as heat, so big transformers are cooled with oil.
Laminated cores cut eddy-current losses
The iron core is a conductor. The changing flux induces an emf in the core itself, and this drives eddy currents in loops around the flux. They produce heat (I²R) and waste energy. To stop this, the core is built from thin sheets (laminations) of iron, each coated with an insulating varnish. The insulation stops the current from crossing between sheets, so each eddy-current loop is small. A small loop has a small emf, so much less heat. If the sheet thickness is cut to 1/n, the eddy heating falls to about 1/n². So 10 sheets give about 1/100 of the loss. The sheets must still carry the flux (they lie along the flux direction).
Try it: increase the number of sheets and watch the heat drop. Then remove the insulation: the sheets touch and the big loops return.
Send power at high voltage, low current
Power lines have resistance, so they lose power as heat: loss = I²R. The current needed for a power P at voltage V is I = P ÷ V. So the loss is (P ÷ V)² R. If we step the voltage up by 10, the current falls to 1/10 and the loss falls to 1/100. That is why power stations use step-up transformers to send electricity at hundreds of kilovolts, then step-down transformers near homes make it safe (230 V in Nigeria and the UK, 120 V in the USA).
Try it: send 5 MW at 11 kV: huge loss! Move the voltage slider up and watch the loss fall away.
Worked example 6: 5 MW is sent through cables of total resistance 10 Ω at 132 kV. Find the current and the power lost.
- I = P ÷ V = 5 000 000 ÷ 132 000 = 37.9 A.
- Loss = I²R = 37.9² × 10 ≈ 14 kW (only 0.3% of 5 MW).
- At 11 kV the same job needs 455 A, and the loss is 455² × 10 ≈ 2.07 MW (41%)!
Which loss? Which remedy?
Sort each item under the loss it belongs to.
True or false?
Each statement sounds sensible, but some are wrong. Pick True or False.
Let’s do one together
🔌 Problem: A transformer has 1000 turns in the primary and 50 turns in the secondary. The primary is connected to 240 V AC. The secondary drives a 6 Ω lamp. Assume it is ideal.
Exam-style practice
Type only the number. Use F = BIL, Φ = BA, ε = NΔΦ ÷ Δt, ε = BLv, Vs ÷ Vp = Ns ÷ Np, η = Pout ÷ Pin × 100%, loss = I²R.
How to write a top answer
Faraday: “The induced emf is directly proportional to the rate of change of flux linkage.” Lenz: “The induced current opposes the change that causes it.”
Use “because”. For example: the core is laminated because the insulation stops big eddy currents, so there is less heating.
Write the formula, the numbers, and the answer with its unit. Change cm to m first.
🔗 Match each question word to what you should do
✔ Exam-style questions
Match each word to its meaning
Tap a word, then tap its meaning. (On a computer you can also drag a word onto its meaning.)
Show what you know!
25 questions in WAEC, IGCSE/A-level and American (SAT/AP) style, getting harder as you go. You will see feedback after every answer.
The 10 things you should remember
Tell a friend why a transformer does not work with a battery and why the power lines use very high voltage.
Lesson complete!
Brilliant work exploring electromagnetic fields, forces, induction, generators and transformers. You can jump back to any part using the map below.